.Military blockers|Military vehicle barricades|Military tire breaker
2.Military remote control barricades
3.Military remote-controlled tire breaker
4.Military remote control vehicle barricade nails
I public production blockcar nail factory, blocking car nail application, military blocking nail grand Kaisheng blockcar barricade nail production, Beijing blocking car barricade nail factory
Xi'an remote control car barricade nails, Chengdu remote control car blocking roadblock nails, Chongqing remote control car blocking roadblock nails, Wuhan remote control car blocking roadblock nails, Qingdao remote control car blocking road blocking nail, Hangzhou remote control car blocking roadblock nail, Nanjing remote control car blocking roadblock nail, Shanghai remote control blocker roadblock nail, Suzhou remote control blocker roadblock nail, Wuxi remote control blocking car roadblock nail, Grand Yangzhou remote control car barricade nail, Nantong remote control blockcar roadblock nail
Rigi brand stainless steel remote control tire breaker introduction:
Floor-mounted remote control tire breaker by Beijing Grand Kaisheng Industrial Co. , Ltd. research and development of a high-performance portable remote control block barricade nail, it is composed of high-performance reinforced plastic blocks and stainless steel gas hollow needle combination, the use of mechanical and electrical remote control device, easy operation, safe and reliable, ready to set up a card, flow of cloth, does not affect the normal road flow, It is the relevant law enforcement departments, the need to set up cards to intercept suspects when the vehicle indispensable advanced equipment.
The tire breaker can be rolled up and put into the box, easy to carry. And each set of "tread breaker" also equipped with a small white remote control, car inspection, the tire breaker out, laid in the temporary set up on the section of the barrier, as long as the hand grip remote control, you can control the tire breaker in the range of 150 meters. Press the remote control, the tire breaker immediately erected two rows of dense arrangement of hollow spikes, nail tip upward. As the vehicle passes, the front and rear tires are pierced by hollow spikes. After more than 20 meters ahead, all four tires were flat. "But it doesn't cause a flat tire, which keeps the driver safe while stopping the vehicle within 200 meters." Then, press the remote control again, the hollow nails immediately retract, other vehicles can pass safely. It is a military equipment for police officers to exercise road traffic control.
Beijing Grand Kaisheng Industrial Co., Ltd. is a professional in traffic safety facilities products manufacturers, set development, production, sales, parking lot construction, road demarcation project construction of specialized companies in one of the large-scale transportation facilities leading enterprises. Continuous innovation, is committed to the creation of the most suitable products for users, better and faster customer service, and jointly create a better future. Our goal is only one, because, hello I am good - this is the voice of every employee of Kequan Industrial, but also our Kequan Industrial to provide a full range of traffic safety facilities the ultimate purpose. Serving all the people in the community, building a one-stop trading supermarket for traffic safety facilities, we are not only trying, but also in the active efforts. Honesty-based, win-win cooperation, is Beijing Grand Kaisheng Industrial to customers forever commitment. May our sincerity can be exchanged for your trust in us, Kequan Industrial will be the highest enthusiasm, the most exquisite technology, the most excellent product quality to provide you with the best service!
Beijing Grand Kaisheng Industrial Transportation Facilities Manufacturer: 24-hour service hotline 13601303513 Shona 010-81535399.www.jsn110.net
Remote control automatic/Manual dual-use portable blocker nails
Description of the use of the product:
l The blocker pin is placed on the road surface - the traction unit unfolds - open the two sides of the latch - open the traction unit power switch (red key lights up as standby).
l Pull out the remote control antenna - press the forward key (front side) and the nail band expands to the desired length to release the key.
l When receiving, press the back key (back side) to press the back key almost to let go.
l Note: The circuit board has a delay function, the operation must be good in advance, otherwise it will cause damage due to strong inertia impact box.
l When the box is collected, the traction device should match the nail case interface, then put up the box and press the locking on both sides.
l Choose a flat road environment when laying the operation.
l When remote control cannot be operated due to mechanical and electrical faults, the nail belt can be pulled out by hand-held traction device and the laying is done manually.
l Precautions: (Please read the instruction manual carefully before use).
l Because the nail is sharp, in operation, maintenance care to avoid injury.
General fault judgment and maintenance:
1. In the event of a remote control failure, please check below:
l Check that the remote control power supply is correct (if the battery of the remote control needs to be replaced).
l Check that the power supply to the gear box is ok. The main lithium battery normal charging once, can be continuousremote control storage100Sub-or continuous standby100New batteries should be considered for hours or more if the working age of equipment drops significantly.
l Check that the board is OK (the board light is on when the power supply is on).
2. If due to the nail belt (aluminum strip) deformation caused by the normal storage, please adjust the deformed aluminum strip by hand straight can return to normal.
3. This product is mechanical and electrical products, in case of special circumstances can not be restored to normal use, please contact the supplier, according to professional skills
4. Roadblock facilities staff prompt to troubleshoot, non-professionals are strictly prohibited from self-dismantling.
Product specifications, indicators:
l Outer box size:550mm x425mmx80mm。
l Weight of equipment:8 Kilograms.
l Remote speed:5Expand in seconds7Meters 5Retractin in seconds 7MetersThe required length is freely chosen.
l Remote control range:50Meters.
l Nails Long:4.5mm.
l Charging rules: The first three charges need to be filled each time12Hours. Continuous collection and release operations100More than, continuous standby100hours or more. The charger indicates that charging is on when the red light is on and that the charge is complete when the green light is on.
l This product is covered by one year. (Damage caused by unusual operation is not covered by warranty) 
