Brand Shanghai Solid Type Car Ground Lock
Model GJ05-10 material high-quality cold pull steel
Suitable for all models of all models of the scope of use of parking, underground garage
The company invented and produced patented products--- triangular manual parking lock is the reason why the vast number of users are over:
First, the use of materials and reasonable structure and process support (half a million yuan of workfitting and mold fixtures):
1, the chassis of the patented product is the use of 2.5 mm thick high-quality cold-rolled steel plate overall stretchforming forming, production equipment with 300 tons press, four pay large mold (material mold, stretch mold, plastic mold, cut edge mold) plus six pay punch mold, with 200,000 yuan tooling mold production chassis patented product advantages are: the overall forming clean and beautiful and strong Around is the arc corner does not hurt the tire, with mold production of large quantities of high accuracy, product soldering life is long. The disadvantage of imitation products produced without mold is: chassis with a few pieces of less than 1 mm of ordinary hot plate welding, neither beautiful nor strong, not only right-angle edge injury tire, and welds easily rust cracking directly affect the service life.
2, the patented product of the gear lever two are made of 60 x 40 mm, thickness 2.5 mm rectangular steel pipe, production equipment with 60 tons of punch, three pay medium-sized mold (cut edge mold, punch ingenhole mold), two gear rod bottom end welding a 20 mm diameter shaft, the shaft installed in the bearing seat, The advantages of patented products are: two square steel pipes made of the gear rod combined, anti-collision and pressure effect is good. The disadvantage of imitation products is that a U-shaped pole is made of hot plate folding, Another gear pole is made of 1.5 mm thick rectangular steel pipe, and eliminates two hinges, only drilled a hole at the lower end of the U-shaped, the hole pierced into an M12 screw and chassis connection, anti-collision pressure effect is obviously poor, to put the parking lock down the tube side into the hot plate rod groove, a little attention will be the finger, and the head of the bend No strength as a kick is deformed.
3, the patented product bearing seat a set of four all 2.5 mm thick cold pull steel plate production, aluminum alloy bearings, the advantages of patented products are: durable and not rusty. The disadvantage of imitation products is: no bearing seat, with drilling holes in the 1 mm thick chassis wall instead of the bearing seat, no strength to speak of.
4, the patented product lock core using anti-theft durable all-copper lock core plus three keys, the advantage is: anti-theft effect is good not to worry about rust, three keys in the two pieces to the owner, a piece of property (security). Imitation product disadvantage is: zinc alloy of the ordinary lock core anti-theft effect is very easy to rust, two keys easy to lose, property (security) hands no key management is very passive.
5, patented products of the latch, latches made of brass, spring with stainless steel wire, the advantages of patented products are from all aspects to fully consider rust prevention to extend the life of the product. The disadvantage of imitation products is that they do not use brass and stainless steel, at the expense of low-cost competition for quality.
Second, the use of effort without squatting:
The advantages of patented products are: lock core from the ground 38 cm high, people as long as a little bend ingestcand can be inserted by hand key to open the parking lock, imitation product disadvantage is: lock core from the ground only 4 cm high, people should completely squat and head down to see the keyhole, and then insert the key by hand to open the parking lock.
Third, the easiest to use the most easy, whether open or latching only need one action to complete:
1. Open parking space: the advantage of patented products is - open the parking lock only one hand insert key to turn 90 and deg; The disadvantage of imitation product is that when ———— open the parking lock, you need to hold the left-hand lever with your left hand, use your right hand to insert the key to turn the key through 90-deg, then pull out the key with your right hand to push the right-hand lever into the U-shaped groove of the left-hand lever (note: don't lock the left-handed finger), and finally put the carrier lever into the slot of the chassis with both hands.
2. Lock parking space: the advantage of patented products is - just pull the right stop lever up with your left hand to the highest point, two levers automatically become triangles and automatically lock, an action easily completed (lock parking space lock does not require the use of keys benefits are: in residential areas or business units, The owner can drive the car directly away from the parking space without parking himself to get off the locked parking space lock, which can be replaced by the steward or security guard). The disadvantage of imitation product is - lock the parking position lock with the left-hand lever pulled out of the chassis slot, with the right hand to pull the right-gear lever from the U-shaped groove of the left-gear lever, push to the right end of the chassis slot, the lower end of the right-grade pole to the locking shaft in the chassis slot, and then squat down with the right hand to push the lock core in, A few movements plus the time-consuming and laborious squats.
Fourth, the advantages of patented products are: can be used for parking space anti-occupancy, but also can be used for vehicle anti-theft, but also to solve their own demolition and theft problems. The chassis has 4 closed holes, the nut of the expansion bolt is tightened and poured into cement or colloid to bury the nut, the socket wrench can not touch the nut, so it can prevent theft. Nuts of other types of products are exposed and easily stolen.
Fifth, the advantages of patented products are: do not worry about being crushed by the wheel deformation and scrap. Chassis is made of 2.5 mm high-quality cold pull steel plate, the interior is equipped with 14 pressure-resistant pillars, and there are two 2.5 mm wall-thick square steel pipe (gear rod) pressure resistance, so strong and not afraid of pressure. Other types of products are made of 1mm steel, saving material but not being crushed by wheels.
Six, the advantages of patented products are: the overall outer surface is an arc shape, both beautiful and will not scratch the tire, and the use of outdoor powder spray does not fade off, in the front and rear of the gear pole on the front and rear of the four 3M imported reflective film, reflecting the golden light at night. Other types of products are right-angle dying, easy to scratch car tires, the appearance of easy leg color easy to rust, no reflective film easy to be hit by the car.
