细节展示放大镜特效

Pneumatic Lift Rod Manufacturer

  • No:T5-110-1500-6000
  • Quantity:
    Product Profile:
    Universal lifting rodOur company independently developed a multi-segment telescopic rod with cylinder as the core. The product has the characteristics of multi-section synchronous expansion, high load, high adaptability, low failure rate and low sloshing rate. It can replace hydraulic and screw expansion devices, and has very broad application prospects in lifting, lifting and erecting fields.

    Applications:
    Military communication, missile, radar antenna erecting device; public security anti-lifting monitoring; fire emergency lighting at night; mobile lightning rod; lifting and lifting equipment.

    Technical Introduction:

    In terms of working principle and technical characteristics, the mast is equivalent to a multi-section cylinder. When in use, air is injected and discharged into the cylinder to realize the upward and downward motion of each section of the cylinder.

    Each cylinder is made of high-quality aluminium alloy material. The whole manufacturing process includes extrusion forming, cold drawing, honing, machining, anodic oxidation and other technologies. The quality of mast is guaranteed through strict inspection procedures.

    If you want to know the structure of the mast, please refer to the mast structure chart. If you want to know more, please refer to the relevant technical instructions, or with Nanjing Snow CodeCompany contact. You will find the advantages of this kind of mast: simple structure, but precise manufacturing process, so easy to use, stable performance, is your ideal product.

    The specifications of masts are determined according to the number of knots, the maximum outside diameter of knots, the initial height and the maximum height. The technical performance of masts with different specifications is different.

    Technical parameters:
    Maximum lifting height (unfolding height): 1-30M (customizable according to requirements, common specifications see the attached table);
    L Closure height: 500MM-4000MM (customizable);
    L Load: maximum load 500Kg, minimum load 5Kg (refer to common specifications);
    L Lifting time: 2-3M/min;
    L Maximum yaw angle: 5 & deg;
    Maximum torsion angle: 45 mrad;
    Level of wind resistance: Level 8 wind energy works normally, Level 10 wind is not destroyed;
    All the above parameters are the parameters of the lifting pole of the company's general model.


    Our company has the advantages of pneumatic lifting rod:
    1. Low failure rate
    The mast is made of national grade aluminium alloy 6061, 6063 and stainless steel. It is driven by air pressure and has cylinder inside. It has simple structure, much lower failure rate than other driving modes, and easy to use and maintain. The other internal structure is complex, and it is easy to produce the phenomenon of wire rope winding. After rising, it is difficult to descend.
    2. Light weight
    Internal reduction of gear and steel wire accessories, the use of air pressure as a driving force, does not increase the weight of self-weight. For example, the weight of the 6-meter electric lifting rod is 80 KG, while that of the 6-meter pneumatic lifting rod is only 30 KG, which greatly reduces the damage of the lifting rod to the vehicle chassis.
    3. Good sealing, dust and sand control
    Pneumatic lifting mast requires higher sealing requirements, so the sealing is the best, which can effectively reduce sand, gravel, etc. into the rod body, scraping the rod surface.
    4. Rotation-proof
    Each section is connected by a guide key, and the whole body can prevent rotation at any height.
    5. Small wind swing
    Because the pneumatic rod adopts a high-sealed protective ring, the mechanical gap between the nodes is very small. When the rod rises, it has high stability and is not easy to sway. At present, the realizable sway of our company is less than & plusmn; 30mm. And the minimum swing of other rods is less than & plusmn; 200 mm
    6. Strong environmental adaptability
    The mast is made of aluminium alloy, stainless steel and other materials. Its surface is treated by anodic hardening. It is anti-corrosion and rust-proof. It is not afraid of saltwater, immersion and ultraviolet radiation. The working temperature range of pneumatic lifting rod is - 55 ~80 C. The electric lifting rod is only - 50 ~70 C.
    7. Important load
    The maximum load of the pneumatic lifting rod can reach 500 kg, while the other rods are only about 200 kg.
    8. High safety
    The pneumatic lifting rod adopts pneumatic lifting, which has pneumatic protection inside the rod body, causes accidents and pneumatic cushioning protection, and will not fall down directly from a height of more than 10 meters. The other rods are different because of the wire rope inside, after lifting, the high load plus the weight of the rod body, the steel wire will easily come out because of the high load for a long time. The rod falls directly from high altitude, causing damage to antenna equipment.

    Common specifications:
    Ordinary type
    T3-110-1600-4000
    T4-110-1900-6000
    T5-110-2000-8000
    T5-110-2350-10000
    T7-150-2600-12000
    T7-215-3100-15000
    T8-215-3300-18000
    military version
    T3-110-1600-4000/J
    T4-110-1900-6000/J
    T5-110-2000-8000/J
    T5-110-2350-10000/J
    T7-150-2600-12000/J
    T7-215-3100-15000/J
    T8-215-3300-18000/J
    Total height (m)
    4
    6
    8
    10
    12
    15
    18
    Closure height (m)
    1.6
    1.9
    2
    2.35
    2.6
    3.1
    3.3
    Maximum diameter (mm)
    118
    118
    118
    118
    160
    229
    229
    Minimum diameter (mm)
    82
    66
    51
    51
    51
    98
    82
    Number of Bar Nodes
    3
    4
    5
    5
    7
    7
    8
    Base diameter (mm)
    180
    250
    340
    Bearing capacity (kg)
    100
    70
    30
    100
    Extreme wind
    When the wind speed is less than 14m/s, no pulling rope is used. After using the wind rope, it can work normally at the wind speed of 20m/s.
    Lifting time
    2-3M/min
    8-stage wind oscillation (mm)
    50
    50
    80
    100
    100
    120
    100
    Self-weight (kg)
    14
    22
    28
    39
    66
    155
    260
    Power Supply
    220V/50Hz (12V or 24V can also be customized for users)
    ambient temperature
    Common type: - 45 ~55 C; Military type: - 55 ~80 C
    Note: Lifting poles of various specifications can be customized according to customer requirements.